How to price filter cleans
    and acid washes

    Filter cleans and acid washes are the two most common one-time jobs on a service route. Here's what each involves, how long it really takes, typical prices, and the risks you need to price in and put in writing.

    Gavin Batson

    Written by Gavin Batson

    Founder, Pool Pro · Updated November 18, 2026

    Prices on this page are typical ranges from local company price lists and national consumer cost guides for 2025 and 2026. They vary by market. Price your own jobs from your time and materials.

    Filter cleans at a glance

    FilterTypical priceTime on siteTypical frequency
    Cartridge (single element)$80–$12530–45 minEvery 3–6 months in year-round markets
    Cartridge (multi-element, 4 cartridges)$100–$17545–75 minEvery 3–6 months
    DE (teardown, clean grids, recharge)$100–$200 including DE45–90 minOnce or twice a year, backwash in between
    Sand (sand change)$250–$400 including sand1.5–3 hoursEvery several years, backwash in between
    Cartridge deep clean (degreaser or acid soak)+$25–$60 over a standard cleanExtra trip or a swapOnce or twice a year

    Typical ranges. Local price lists from Arizona and Texas pool companies show cartridge and DE cleans at around $80–$100 and sand service at $300–$350. A homeowner can buy DIY cartridge cleaning supplies for $20–$40, which is a useful reminder that what you're charging for is time and skill.

    Cartridge filters

    The most common filter on residential pools built in the last 20 years in much of the Sun Belt. A standard clean means shutting the system down, releasing pressure, opening the tank, pulling the element or elements, hosing every pleat from top to bottom, checking the tank and lid o-ring, reassembling, bleeding the air and confirming the start-up pressure.

    • Time: 30–45 minutes for a single element, longer for four-cartridge filters and for heavily loaded ones that need to be hosed twice.
    • Frequency: when the pressure is about 8–10 psi above the clean starting pressure, which on most pools means every 3–6 months, sooner after a heavy pollen season, a green-pool recovery or a phosphate treatment.
    • Deep clean: hosing doesn't remove oils, lotions and scale. A soak in a filter degreaser (and, for scale, a diluted acid soak after degreasing, never before) restores flow. Many companies keep a spare set and swap them, then clean the dirty set back at the shop.
    • Replacement: elements wear out after a few years. Torn fabric, crushed pleats, or pressure that rises again within weeks of a clean means it's time. Quote replacement elements as parts plus your markup.

    DE filters

    DE (diatomaceous earth) filters filter the finest particles, and they're the most work to clean properly. Backwashing between cleans removes some of the dirt and old DE, but grids still clog over time. A full clean is a teardown:

    1. Shut down, release pressure, drain the tank.
    2. Remove the grid assembly and hose each grid and the manifold.
    3. Inspect grids for tears and the manifold for cracks. A torn grid sends DE into the pool.
    4. Check and lubricate the tank o-ring, reassemble.
    5. Start the pump and add the correct amount of DE through the skimmer, as printed on the filter's label.
    6. Record the new clean pressure.

    Allow 45–90 minutes. Include the DE in your price and say so. Damaged grids, manifolds and air relief valves are extras.

    Check your local discharge rules. Many cities and counties restrict draining DE and backwash water into the street or storm drain. Some require a separation tank or bagging the spent DE. Ask your city or county stormwater office what applies before you hose a DE filter out on the driveway.

    Sand filters

    Sand filters are cleaned by backwashing, which the tech does as part of regular service when pressure rises. The billable job is the sand change, when the sand has worn smooth or clumped and no longer filters well. That's commonly every several years, depending on the load.

    A sand change means draining the tank, removing the multiport valve, shoveling or vacuuming out the old sand without damaging the laterals, inspecting and replacing broken laterals, refilling with the right grade and weight of filter sand (or an alternative media) and reassembling. Plan 1.5–3 hours and a sore back. Price includes the sand, haul-away and your time. Broken laterals and a worn valve gasket (spider gasket) are common add-ons, so quote them as possible extras up front.

    Include filter cleans in the monthly price, or charge separately?

    Both are common. It depends on your market and how much your filters vary.

    • Included: common in Florida and in competitive markets where customers compare flat prices. Build it into the rate. For example, two cartridge cleans a year at $100 each is about $17 a month.
    • Separate: common in Arizona and Texas. Keeps the monthly price lower and pays you for the extra work on dirty pools. Schedule cleans on a calendar (for example, cartridges every three months and DE every six) rather than waiting for the customer to ask.
    • Hybrid: one or two cleans a year included, additional cleans billed. This works well for heavy-debris pools.

    Whichever you choose, write it in your service agreement. "Filter cleans billed separately" is the line customers forget most, and the one that causes the most disputes.

    Acid washes and drain-and-cleans

    An acid wash strips a very thin layer off a plaster (or similar cementitious) surface to remove stains, scale and algae that brushing and chemicals can't reach. It means draining the pool, washing the surface with diluted muriatic acid, neutralizing and removing the acid water, rinsing, refilling and restarting the chemistry.

    A drain-and-clean is the same job without the acid: drain, pressure wash and scrub, rinse, refill. It's used when the water itself is the problem (very high stabilizer, high calcium or dissolved solids, a pool that sat green for months) and the surface is in decent shape.

    When an acid wash is the right call

    • Widespread organic or algae staining that stain treatments and brushing didn't lift.
    • A pool left green or black for a long time, where the plaster is discolored after the water is cleared.
    • Light scale and mineral staining on plaster, after you've ruled out metals that will come right back.

    Every acid wash removes some plaster, so the surface can only take a limited number in its life. Try a no-drain stain treatment, a chlorine wash or a drain-and-clean first where they'll do the job. Never acid wash vinyl liners, and check the manufacturer's guidance before draining or treating fiberglass.

    Typical prices

    JobTypical priceNotes
    Drain and clean (no acid)$400–$700Pressure wash, scrub, rinse, refill
    Acid wash$300–$700 for most residential poolsOften quoted as roughly $0.50–$0.75 per square foot of surface
    Chlorine wash$300–$600For organic stains. Often combined with an acid wash
    Acid wash plus chlorine wash+$100–$200 over an acid washTwo treatments, one drain
    Start-up chemistry after refill$100–$250Balancing fresh water, stabilizer, calcium, and the first few days of chlorine
    Heavily stained or very large pools$800–$1,500Multiple passes, more acid, more labor

    Typical ranges. National consumer cost guides line up: most residential acid washes run $300–$700 (about $0.50–$0.75 per square foot), a typical job lands around $450, and a full drain and clean commonly runs $500–$700.

    Worked example: pricing an acid wash

    A 16 × 32 foot plaster pool, 3.5 to 6.5 feet deep, about 15,000 gallons and roughly 1,000 square feet of surface:

    CostEstimate
    Setup and starting the drain (submersible pump, discharge hose)1 hour × $35 loaded = $35
    Acid wash and rinse, two techs2 × 4 hours × $35 = $280
    Muriatic acid and soda ash to neutralize$60–$90
    Return trips: pump check, start refill, start-up chemistry2 trips × $40 = $80
    Start-up chemicals$40–$70
    Total costabout $495–$555
    Price at a 35–40% marginabout $760–$925

    That's above the national average, which tells you something: at $450 this job barely pays if you do it properly with two people. Either price at the top of the range or get faster. Owners who do these often build the job around waiting time, starting the drain at the end of a route day and washing first thing the next morning.

    Water cost: who pays

    The refill comes off the customer's water meter, so it's on their bill, and the quote should say so. A 15,000-gallon refill at a combined water and sewer cost of $5–$15 per 1,000 gallons is about $75–$225. Budget roughly $90–$270 for a typical refill. Some utilities offer a sewer credit for pool fills, because the water doesn't go down the drain. Tell the customer to ask, and they'll remember you for it.

    Draining also has rules. Many places require you to let chlorine dissipate, neutralize acid water to a near-neutral pH and discharge to the sanitary sewer cleanout rather than the street. Check with the city before the job, not after a neighbor complains.

    The risks, and how to price and paper them

    Hydrostatic pressure

    An empty pool is a boat in wet ground. If the water table is high, from heavy rain or a nearby lake or canal, groundwater pressure can push the shell up or crack the floor. That damage costs far more than the job.

    • Don't drain right after heavy rain, or in the rainy season in high-water-table areas.
    • Check for a hydrostatic relief valve in the main drain sump and know how to open it.
    • Keep the pool empty for as few hours as possible. Wash, rinse and start the refill the same day.
    • Fiberglass and vinyl pools are especially vulnerable. Many companies won't drain them at all.

    Plaster

    Old or thin plaster can show its age once it's stripped: rough spots, exposed gunite, delamination (hollow spots that pop off). A wash can make a pool that's near the end of its finish life look worse, not better. Look before you quote, and tell the customer when replastering is the honest answer.

    Put it in writing

    Every acid wash and drain should come with a signed estimate that says:

    • Stains may not come out completely, especially metal stains.
    • Draining carries a risk of hydrostatic damage, and the steps you take to reduce it.
    • Pre-existing plaster damage may become more visible.
    • The customer pays for refill water.
    • What's included in start-up chemistry and when regular service resumes.

    Our repair estimate template has room for these terms. Also check what your liability policy says about draining and chemical damage. See pool service insurance.

    Add-ons worth offering

    • Chlorine wash for organic stains, with the acid wash, on the same drain.
    • Start-up chemistry package with a fixed price for the first week after refill.
    • Filter clean on every acid wash. The filter catches whatever comes off the surface.
    • Tile cleaning while the pool is empty and the tile line is easy to reach.
    • Equipment inspection and small repairs (o-rings, light niche, drain cover) while the pool is drained.
    • Weekly service for customers who don't have it yet. A freshly washed pool is the best sales pitch you'll get.

    Bill filter cleans and add-ons when the work is done, not at the end of the quarter. In Pool Pro, invoices are generated automatically from completed work and customers pay online, so a $100 filter clean doesn't turn into a bill you forget to send.

    Common questions

    How often should a cartridge filter be cleaned?

    When the pressure is about 8–10 psi above its clean starting point. On a typical year-round pool that's every 3–6 months. Record the clean pressure on the filter or in your logs after every clean so any tech can tell at a glance.

    Should I charge more for a four-cartridge filter?

    Yes. Four large elements take noticeably longer to pull, hose and reinstall than one. A $25–$50 premium over a single-element clean is common.

    Can I acid wash a pool without draining it?

    Not a true acid wash. There are no-drain stain treatments that lower pH and use acid or stain removers in the water, and they're a good first step for mineral stains. They're a different job with different pricing.

    How long does a pool have to be empty for an acid wash?

    As short as you can make it. Draining often runs overnight, and the wash and rinse take a few hours for a typical residential pool. Start the refill as soon as the rinse water is out.

    Do I need a license to drain and acid wash pools?

    In some states, yes. Florida, for example, requires a pool/spa servicing contractor license for substantial draining for repair. Check our guide to whether you need a license to clean pools and your state's page before you take these jobs.

    What should a sand change cost the customer?

    Commonly $250–$400 including sand and haul-away. Quote broken laterals and a multiport gasket as likely extras, since you won't know until the tank is open.

    Run your pool business from one place.

    Pool Pro handles scheduling, route optimization, chemistry logs and automatic billing. Plans start at $35/month.

    Route optimizationAutomated invoicingChemistry logs with LSI