Pool opening checklist
- Confirm the customer is expecting you and the gate, dogs and power are sorted
- Walk the deck: note cracks, loose coping, missing tiles, debris on the cover
- Photograph the cover, equipment pad and anything already damaged
- Pump standing water and leaves off the cover (solid covers) before pulling it
- Remove the cover; release safety cover springs with the install tool
- Clean the cover, let it dry, fold and store it off the ground
- Screw anchors down flush with the deck so nobody trips
- Remove water bags, air pillow and any skimmer covers
- Pull winter plugs from skimmers and returns; reinstall return eyeballs
- Remove any skimmer winterizing device (ice compensator)
- Reinstall drain plugs on pump, filter, heater and chlorinator
- Reconnect any equipment removed for winter (pump, salt cell, chlorinator, cleaner)
- Reinstall ladders, handrails and diving board; check bolts and bumpers
- Inspect pump lid O-ring, filter tank O-ring and valve gaskets; lube with silicone lube
- Top up water to the middle of the skimmer opening
- Set the multiport or valves to filter; open suction and return valves
- Open the air relief valve on the filter
- Fill the pump basket with water to prime; close the lid tight
- Turn on power and start the pump; close air relief once water spits out
- Note starting filter pressure: ________ PSI
- Backwash or clean the filter if pressure is high or media is dirty
- Fire the heater only after confirming water flow and no gas or wiring issues
- Pump lid, unions, filter clamp, valves, heater connections
- Look for drips under the equipment and wet spots on the pad
- Listen for air in the pump (bubbles in basket = suction-side leak)
- Note water level now: ________ (recheck in 24 to 48 hours)
- Skim debris; empty skimmer and pump baskets
- Brush walls, steps and floor
- Vacuum to waste if the floor is heavy with debris
- Let water circulate at least a few hours before testing (overnight is better)
- Test: FC ____ pH ____ TA ____ CH ____ CYA ____ Salt ____ Temp ____
- 1. Adjust total alkalinity
- 2. Adjust pH
- 3. Adjust calcium hardness
- 4. Add stabilizer (CYA) if low
- 5. Shock to the level for the CYA reading (see FC/CYA chart)
- Add salt only after confirming the cell is installed and volume is known
- Run the pump 24 hours; leave the customer a note not to swim until FC is back in range
Pool closing and winterizing checklist
- Confirm cover type and condition with the customer (order replacements early)
- Clean the pool: skim, brush, vacuum
- Test: FC ____ pH ____ TA ____ CH ____ CYA ____ Temp ____
- Balance water: pH 7.4 to 7.6, TA and CH in range
- Shock to the level for the CYA reading; let FC come back down before closing
- Add winter chemicals (winter algaecide, enzyme or winter kit) per label
- Clean the filter: backwash or chemically clean cartridges or grids
- Lower water level for the cover type:
- Mesh safety cover: below the skimmer mouth and returns (per cover maker)
- Solid cover with water bags: just below the skimmer, or per cover maker
- Pool with skimmer plugs and no lowering: confirm plugs and ice compensator
- Never drain a pool fully (groundwater can push vinyl and fiberglass pools out of shape)
- Remove return eyeballs, skimmer baskets, cleaner, ladders and rails
- Blow out each skimmer line from the equipment until it bubbles, then plug at the pool
- Blow out each return line until it bubbles, then plug at the pool
- Main drain: blow until bubbles appear, then close the valve to hold an air lock
- Blow out cleaner, spa, water feature and solar lines
- Install a skimmer ice compensator (or a sealed plastic bottle)
- Pool antifreeze (propylene glycol, never car antifreeze) in lines if used locally
- Turn off power to pump, heater, cell and timer at the breaker
- Remove drain plugs from pump, filter, heater and chlorinator; store in pump basket
- Open filter air relief; set multiport to winterize or closed
- Drain heater fully; blow out with low pressure if the maker allows
- Remove salt cell, chlorinator tablets and store indoors
- Store small pumps, cleaners and DE grids indoors if possible
- Safety cover: check anchors, straps and springs; tension evenly
- Solid cover: lay out, fill water bags halfway, overlap bags around the edge
- Use an air pillow under solid covers on above-ground pools
- Photograph the closed pool and equipment pad for the customer file
- Note anything the customer should fix before spring: ______________________
How to use these checklists
Print a fresh copy for every pool, fill in the header at the truck, and work top to bottom. Keep the finished sheet in the customer's file. If a customer calls in May about a leak at the filter, a dated sheet showing you checked the clamp and noted a dry pad is worth more than anyone's memory. Take photos at the start and end of each job for the same reason.
The order matters most in two places: start-up chemistry and blowing out lines. Everything else can be shuffled to suit how your crew works.
Why the start-up chemistry order matters
Alkalinity buffers pH, so if you fix pH first and then move alkalinity, pH moves again and you have wasted acid. Set alkalinity, then pH, then calcium. Add stabilizer next if it is low, because the chlorine you need depends on the CYA level. Shock last, once the water is balanced, so the chlorine does its work instead of fighting a high pH. The chemical calculator gives doses for each step, and the FC/CYA chart shows the shock level for any CYA reading.
Timing by climate
There is no single right date. A common rule of thumb is to close once water temperature stays below about 65°F, when algae growth slows, and to open before the water warms back up to that point in spring. Close too early in a warm fall and the pool can turn green under the cover. Open too late and you are cleaning up algae instead of starting up a clean pool.
- Hard-freeze climates: full winterizing every year. Blow out and plug every line, drain all equipment, and use pool antifreeze where local practice calls for it.
- Mild-freeze climates: many pools stay open and run the pump on a freeze-protection timer or sensor. Some customers still want a partial close with a cover. Know which one you sold.
- No-freeze climates: pools usually stay open year round. Openings and closings here are mostly about seasonal homes and reduced winter service.
Book openings and closings in a tight window and route them by area, the same way you route weekly stops. The season is short and every customer wants the same two weeks.
Opening a green pool
Pull the cover and find a swamp? Stop and reset the job. A green opening is a cleanup, not an opening, and it should be quoted as one before you pour a single jug. Remove heavy debris, get the filter running, balance pH, then raise free chlorine to the shock level for the CYA and hold it there until the water clears, combined chlorine drops to 0.5 ppm or less, and the pool loses no more than about 1 ppm overnight. That can take days and several filter cleanings.
Spell out in your agreement that a pool opened green is billed as a cleanup. The green pool cleanup pricing guide covers how to price it, and the shock calculator works out the dose.
Safety covers vs solid covers
Mesh safety covers anchor into the deck and let rain drain through, so there is no standing water to pump off. They let sunlight through, which means more algae risk in a warm spring, and they need the water lowered below the skimmer and returns so ice and water cannot damage the plumbing. Follow the cover maker's level.
Solid covers block sunlight, so pools usually open cleaner. They collect rain and leaves, so somebody has to pump the cover through winter, and they are held down with water bags or blocks rather than anchors. A solid cover held with water bags is not a safety cover, and you should never describe it to a customer as one. Solid safety covers anchored into the deck do exist and combine both: clean opening, anchored install, but they still need a drain or pump.
Note the cover type on every closing sheet and check its condition. Torn straps, broken springs and missing anchors are easy add-on sales, and finding them in October beats finding them in a storm.
What to charge
Openings and closings are flat-rate jobs priced by pool type, size and cover, with chemicals either included or billed on top. Price the closing to cover the blowout, the winter chemicals and the time on site, and price the opening with a clear line for what happens if the pool is green. The full breakdown, with how to package both as a seasonal bundle, is in pool opening and closing prices. If you bill chemicals separately, see charging for pool chemicals.
Common questions
Can I use car antifreeze in pool lines?
No. Use pool antifreeze, which is propylene glycol based and made for pool plumbing. Automotive antifreeze is ethylene glycol, which is toxic and does not belong anywhere near pool water.
Should I drain the pool all the way to close it?
No. Lower it only as far as the cover type needs. An empty in-ground pool can be pushed up or out of shape by groundwater, and vinyl liners can shrink and pull loose.
How long should the pump run after opening?
Run it around the clock for the first day or two so the water mixes and the shock does its job, then drop to the normal schedule once readings are stable.
Do I need to shock when closing?
Yes, a few days before you cover it, then let chlorine fall back toward normal so it does not bleach the cover or a vinyl liner. Add winter algaecide or a winter kit on closing day.
What should I record on the sheet?
Readings, chemicals added, starting filter pressure, cover type and condition, and anything that needs fixing. Those notes become next season's opening plan and, often, a repair estimate. The repair estimate template is ready when you find something.
Can I skip the paper?
Yes. In Pool Pro, techs log readings and photos at the pool and every visit is saved to the customer's history, so the opening crew in spring can see exactly how the pool was closed.
